mmd monitor/quartztek 30400 esperanza, rancho santa margarita, ca, 92688 phone: (949) 709-5075, fax: (949) 709-3536, www.mmdcomp.com sales@mmdcomp.com 08/17/11 b subject to change without notice pg 1 of 2 revision: m m u u l l s s e e r r i i e e s s 5 5 x x 3 3 . . 2 2 c c e e r r a a m m i i c c s s m m d d o o s s c c i i l l l l a a t t o o r r ?? 5 x 3.2 smd package 6 pin ?? lvpecl output ?? tristate option ?? tape & reel packaging available marking detail mechanical & environmental detail shock mil-std-883, method 2002 cond b solderability mil-std-883, method 2003 vibration mil-std-883, method 2007, cond a gross leak test mil-std-883, method 1014, cond c fine leak test mil-std-883, method 1014, cond a2 reflow solder +260c for 10 sec max line 1 = mxxxxx m = mmd xxxxx = frequency in mhz line 2 = syywwl s = internal code yyww = 4 digit date code (year / week) l = denotes rohs compliant line 3 = xxxxx internal use only may vary with lots black dot to denote pin 1 frequency range 74.250mhz to 161.1328mhz temperature stability (inclusive of temperature, load, voltage, and aging) (see part number guide for options) operating temperature range (see part number guide for options) storage temperature range -55c to +125c supply voltage (v dd ) 5% supply current 75ma max output lvpecl logic ?0? 1.43 vdc typ, 1.60 vdc max logic ?1? 1.10 vdc typ, 0.90 vdc min load 50 ? into v dd -2.0vdc symmetry (50% of waveform) (see part number guide for options) rise/fall time (20% to 80%) 300p sec typ, 700psec max rms phase jitter (12khz to 20mhz) 1psec max phase noise 100 hz = -95 dbc/hz 1 khz = -125 dbc/hz 10 khz = -143 dbc/hz 100 khz = -146 dbc/hz start-up time 10msec max tri-state operation voh = 70% of vdd min or no connection to enable output vol = 30% max or grounded to disable output (high impedance) (see part number guide for options)
mmd monitor/quartztek 30400 esperanza, rancho santa margarita, ca, 92688 phone: (949) 709-5075, fax: (949) 709-3536, www.mmdcomp.com sales@mmdcomp.com 08/17/11 b subject to change without notice pg 2 of 2 revision: pitch pitch 8.00 [.315] tape width 16.00 [.630] direction of feed 180[7 in] reel dia reel dia q1 q2 q3 q4 q1 q2 q4 q3 tape width 1000 qty per reel pin 1 orient. q1 notes: unless otherwise specified 1. applicable standards / specifications ansi y14.5m , dimensions and tolerances eia-481-b , 8 mm through 200mm embossed carrier taping and 8 mm and 12 mm punched carrier taping of surface mount components for automatic handling. 2. dimensions are in millimeters. 3. tolerances are 0.10 [.004] mm unless otherwise specified. 4. do not scale drawing. part number guide mechanical details tape & reel dimensions 5.15 [.203] max 3.35 [.132] max 1.30 [.051] 321 456 1.27 [.050] 2.54 [.100] 1.00 [.039] 0.64 [.025] 1.27 [.050] 2.54 [.100] 1.00 [.039] 1.40 [.055] 0.80 [.031] pin connections supply voltage complementary output output case ground no connection tri-state or no connection pin 4 pin 6 pin 5 pin 2 pin 3 pin 1 mxx.xxx syywwl pin 1 designator located in this area. dimension in brackets are in inches external bypass capacitor is recommended recommended land pattern 5 x 3.2 ceramic smd 6 pads frequency please consult with mmd sales department for any other parameters or options l supply voltage 2 = +2.50 vdc 3 = +3.30 vdc frequency stability 020 = 20 ppm 025 = 25 ppm 050 = 50 ppm 100 = 100 ppm operating temperature blank = 0c to +70c 27 = -20c to +70c 48 = -40c to +85c symmetry blank = 40%/60% a = 45%/55% pin 1 connection blank = no connection h = tri-state packaging blank = bulk t = tape and reel output l=lvpecl mu
|
